A blue CNC plasma control unit and silver gantry over a charcoal water table, cutting a nest of trough end plates and gussets from galvanised sheet, with cage panels and feeder troughs in the background
Home / Projects / Jet Park Cutting Bay

Projects · In-house cutting

Jet Park Cutting Bay: Our Own Trough Plates, Cage Brackets and Stainless Fittings

Our Boksburg workshop now cuts the small steel parts every poultry project needs, on a MetalWise Lite CNC plasma table from our partner AM.CO.ZA.

Project · November 2026 · Jet Park, Boksburg

Every poultry project we run needs small steel parts: feeder trough end plates, brackets for cage frames, gussets for silo legs, stainless rings for killing-cone stands and corner brackets for evisceration tables. For years we bought most of these in, waited for them, and sometimes held up a farm handover because a box of brackets was still on a truck. This year we decided to cut them ourselves, here in Jet Park, and we built the cutting bay with equipment from our partner AM.CO.ZA.

The problem: small parts, big delays

Nobody notices a bracket until it is missing. Then a whole A-frame layer cage line cannot be finished, and the farmer is waiting for birds. We wanted those parts on our own shelf, cut to our own drawings.

The abattoir side felt it even more. An abattoir room fit-out uses a lot of stainless brackets, drip-tray strips and mounting rings, and on jobs like the Bethal abattoir upgrade the timing of those small parts decided when the room could be commissioned.

Why we went back to AM.CO.ZA

We already knew the team. Last month our service people trained with AM.CO.ZA on laser welding, cleaning and marking, which we wrote about in Back to the Bench. So when we started looking at CNC cutting, the first question was simple: which table could grow with us?

We compared a few suppliers. AM.CO.ZA explained the options clearly, answered our questions about sheet sizes and power, and its Johannesburg branch is close enough that we can drive over with a question.

A blue CNC plasma control unit and silver gantry over a charcoal water table, cutting a nest of trough end plates and gussets from galvanised sheet, with cage panels and feeder troughs in the background
The MetalWise Lite cutting trough end plates and brackets in the Jet Park bay.

What we installed

The table. We chose the AM.CO.ZA MetalWise Lite P-1530 CNC plasma and flame cutting table. Its 1500 × 3000 mm working area takes the full sheets we already buy, it has arc-voltage torch height control with collision prevention, and the 7 inch colour controller offers cutting simulation and preview before the torch fires. AM.CO.ZA's MetalWise CNC handbook quotes the table and the plasma power source together, with the power source sized to the steel you cut. For us that is mostly thin galvanised and mild steel, with the odd thicker gusset.

Under the gantry sits the matching 1500 × 3000 mm water cutting table, which takes sheets up to 35 mm thick. The water helps control sparks, smoke and dust and takes heat out of the parts, which matters with galvanised sheet. The cutting grilles have adjustable levelling, as shown in AM.CO.ZA's P-1530 water table video. The table is a DIY assembly that needs a silicone gasket maker for the water seal (not included), and the MetalWise Lite unboxing and assembly video was a big help when our team put it together.

The software. Our drawings go through FABRICAM, AM.CO.ZA's sheet-metal CAM software, starting with the Foundation Core licence on a USB dongle and adding modules as we need them. FabriCAM can also mark letters on plasma-cut parts, as shown in AM.CO.ZA's FabriCAM letter marking video, so every bracket can leave the table with its part code on it. For us that means fewer mix-ups when a box of spares goes to a farm.

Next on the same gantry: a laser for thin stainless

The part that sold us on this table is that it can grow. AM.CO.ZA's P-VERSATILE/KIT is an upgrade kit to integrate a LaserMaster Versatile handheld laser cutting torch with the MetalWise table, so the table moves the laser along the cut path. The kit is the signal interface: a four-pole relay, a relay base and a connector, with 0.25 mm² or thicker signal cable added to suit the site. AM.CO.ZA prefers its own technicians to install it, on a booked callout. Its video on budget CNC laser cutting with the MetalWise table and Versatile laser shows how it works.

That would give us two ways of cutting on one table: plasma for galvanised and mild steel trough plates and brackets, and the laser for thin stainless where we want a cleaner edge. The laser we trained on in October, the LaserMaster Versatile-Lite 2000W, cleans, welds and cuts from one handheld torch. AM.CO.ZA's plasma versus laser comparison helps decide which job goes where.

Illustration of the planned Versatile laser-torch upgrade on the same gantry, with a laser cabinet and chiller beside the table; this kit is not installed on the Jet Park table yet
Illustration of the planned upgrade: a Versatile laser torch on the same gantry for thin stainless parts, which is not installed on this table yet.

What comes off the table

The bay now cuts most of the small steel we used to wait for:

  • End plates and brackets for our trough feeders and cage frames, in galvanised sheet.
  • Rings and frames for killing cones and carcass drip racks.
  • Corner brackets and drip-tray strips for evisceration tables.
  • Replacement parts for older installations, cut from the original drawing instead of waiting for a factory order.
Neat rows of cut parts on a steel bench: stainless rings, corner brackets and perforated drip-tray strips, galvanised U-shaped trough end plates and L-shaped cage brackets
A morning's cutting, sorted for packing: stainless parts at the top, galvanised trough and cage parts below.

Consumables and spares on our own shelf

Our procurement team set up the consumables side the same way we tell farmers to manage spares to keep. Torch parts wear, so we keep a small stock of our own: MetalWise Mach-Two electrodes, nozzles and shields from AM.CO.ZA, plus a spare machine torch with its 7 metre torch set. AM.CO.ZA's plasma consumables page and plasma cutter SKU guide make it easy to order the right part the first time.

A clear four-pole relay, a black relay base, a silver aviation connector, signal cable and a multimeter beside a row of copper electrodes, chrome nozzles, a shield and a retaining cap
Upgrade kit parts and a row of plasma consumables in the spares corner.

Service and support

What made this work was the help around the machine. The MetalWise gallery showed us real installations before we committed, AM.CO.ZA's engineers post installation and repair work on the Machinery Support vlog, and the AM.CO.ZA guide brings it all together. AM.CO.ZA has branches in Johannesburg, Cape Town and Durban.

We are an equipment supplier ourselves, so we know what good after-sales looks like. What we try to give our own farmers is the right equipment and someone who picks up the phone, and that is what we look for in a supplier too.

What it means for our clients

Shorter waits for brackets and fittings, spares cut from the original drawing, and stainless parts made to suit the room. If you are planning a new house, an expansion or an abattoir room, ask us for spares help, look at our spares supply service, or send a quote request. Every project is quoted on its own drawings, so ask for a quote. You can meet the people behind the work on our team page.

What our Poultry Equipment customers say

Verified Google reviews

Questions we get asked

Can you cut a replacement part for an older installation?

Often, yes. Send us the original drawing or a sample and we will check the material and size before we quote.

Which materials do you cut in the bay?

Mostly galvanised and mild steel sheet for trough and cage parts, plus stainless parts for abattoir rooms.

Why a water table?

The water helps control sparks, smoke and dust and takes heat out of the parts, which matters when cutting galvanised sheet.

What do cut parts cost?

It depends on the material, the size and the quantity, so ask for a quote with your drawing.

Ask us about parts and spares.

Contact form